Tesla EVgata diagnostic software

Brand new TESLA software specially developed to satisfy our customers who work hard with these models. With this we offer completely new functionalities, even for the most advanced. Entirely based on our company slogan - TRUE GEAR FOR TRUE PROFESSIONALS!

The software is completely new and there are constant updates, which of course, like all our products, are fully automatic. Our goal is, as always, to make it as easy as possible for our customers.

• The software includes the following features for - Tesla Model S and Tesla Model X mcu1 (nVidia Tegra cpu) up to version 2022.8.10.5

- Scan the available modules in the vehicle and report active and historical alerts

- Air Suspension - Set Ride Height, Service Mode, Force Gallery Pressure, Request Pressure, Live Ride Height, Clear TAS Crash Data

- Brakes/ESP/TPMS – Read/Write TPMS ID for GEN 2 tpms, bleed brakes, steering wheel angle calibration, activate EPB service mode, retrieve versions

- Airbag - Read/write EEPROM, erase crash data (* Model X only); Read Resistance

- Body - ICE Breaker door handles, steering column calibration, rear wing calibration,

- Battery/BMS - Read BMS Serial Number, Reset BMS Switch, Reset Switch Voltage Index, Reset Switch WOT Counter. Special support for connection to a non-car HV battery via CAN-BUS (external 12 volt power supply must be provided to power the BMS)

- Cooling - THC AirPurge Start/Stop, THC Refill\Drain Start/Stop

- Bank - On/off IC on bank

- Live data - Read alerts

- Advanced Features - Auto Vitality Reading, Keyless Driving ON/OFF, Valet On/Off, Showroom On/Off, IC Reset, Master Reset, CID Reset, GW Reset, Allow GW Telnet, Bus Wake, Rails ON, Diag., Enter/Exit Factory Mode, Enter/Exit Development Mode – All functions via VAPI interface

- Warnings - Read all and current warnings

- Read/write configuration, odometer recalibration, Pin-to-Drive, emergency move, Pin-to-Drive disable

These are just some of the features of our software:

1. Our tool can install firmware on the car

2. Can re-use car (adaptation of non-original vehicle modules, reprogramming of used parts modules)

3. Have functions to download current firmware version of car to help change emmc chip to cid if emmc is completely damaged and can't be read. This way our tool allows you to extract car configuration from car without cid and generate files needed for new CID emmc image. So you don't have to worry about the Spansion chip version

4. Our tool can enable GW serial console for CID

5. Has functions for IC bank setup

6. Can backup and restore IC

7. Can retrofit modules via GW/CID configuration

8.Can set the configuration if you do US/EU conversion and swap the radio and charger module

9. Can recode a new battery if it is different from the original

10. Can program key for Model S

• The software includes the following functionalities for - Model 3 and Model Y

- ACTIVATE FACTORY MODE (up to version 2021.4.3). When Factory Mode is enabled, you have access to all service functions

- CLEAR PIN TO DRIVE

- REPLACE

- CHANGE GATEWAY CONFIG (Activate/Deactivate Supercharger, Autopilot, Change Country...)

- ADD PARAMETER

- UPDATE MAPS

- CHANGE MAP AREA

- CONVERT US TO EU
- READ and export Secure Config from Gateway for 2021+ models with locked MCU over LAN

- TRANSFER configuration to DUMP, ready to program to new MCU (2021+ models)

- Prepare a file to program with different programmers such as PEMicro, XPROG….

- Functionalities via CAN BUS such as - Live data, body component calibration, seat calibrations, Windows calibrations, steering column calibration….

- AIRBAG VIA CAN BUS - Read/write eeprom, Clear crash (until 2021); Check the resistance….

- DIAGNOSIS - Warnings/DTCs; Vital….

- Online update via our server for all mcu2 cars with Ape HW 2.5

READ and Export Secure Config from Gateway

Configuration of the car

Original configuration

NEW configuration

Updates:

There is an annual subscription that is paid after the first year has expired. The prize is €300 for each subsequent year.

All software with an active subscription has automatic updates (after starting the software and connecting to the Internet, the software is upgraded to the latest version). At the same time, most updates are performed on the server side.

Subscribed customers receive our updates regularly. An expired subscription tool will not receive regular updates.

• To use the software, you must already own some of the hardware or purchase it together with the software.

Online support (AnyDesk or SupRemo) - 50 euros/hour

Annual subscription after the first year - 300 euros

* PCAN interface (or compatible) - This is for customers who already have such an interface, our software can work with it too.